Is the weld seam in ERW pipe strong?

Home > Blog > Is the weld seam in ERW pipe strong?

The weld seam in ERW steel pipe is strong when the mill controls heat, pressure, and inspection, and when the pipe meets a recognized standard such as ASTM A53 or API 5L. Modern high-frequency welding fuses the strip edges without filler metal, and heat treatment of the seam refines the grain structure in the weld zone. Hydrostatic, mechanical, and non-destructive tests then confirm the result. I will show you how seam strength is measured, which standards apply, what to ask a supplier, and how to buy with confidence, especially if you resell from stock.

ERW steel pipe

ERW steel pipe

What Makes the Weld Seam in ERW Steel Pipe Strong?

How the Seam Is Formed

A mill flattens a steel strip, cuts it into strips of the right width, and rolls each strip into a circle. Then, high-frequency current warms the two ends of the strip enough so that they can be joined. Squeeze rolls finish the job. In this method, extra metal is not needed because the ends stick together immediately. The squeeze moves a little metal piece called flash out of the way. Both the outside and, most of the time, the inside are cut away by the mill. For high-frequency welding, API 5L says that the current must be at least 70 kHz. The gap is made of the same steel as the pipe itself. This keeps the weld's chemistry the same all the way through.

What "Strong" Means in Measurable Terms

It's just a number; you can't feel strong. When does a sample start to change shape for good? The yield test tells you that. The tensile test tells you how much weight it can hold before it breaks. So, for ASTM A53 Grade B, the tensile strength must be at least 415 MPa (60 ksi), and the yield strength must be at least 240 MPa (35 ksi). To see if the weld is flexible, it can be flattened and bent. You can't bend a seam that breaks or opens up when you bend it. Another way to show that the pipe is strong enough to hold pressure is to test it with water. Buyers shouldn't just trust a general claim; I think they should look at the mill certificate and see these proofs.

What Weakens a Seam

Flaws in the process, not the ERW steel pipe method itself, cause weak seams most of the time. It will be a cold weld if you don't use enough heat. The edges will touch but not fully fuse. The same mistake can happen if the line is moving too quickly or if the edges are not lined up properly. Hook cracks are small flaws that show up when you squeeze something. They might happen because of flaws or dirt on the strip's edge. A weld zone that hasn't been treated with heat can be harder and less flexible than the body, so it's important to do it at the seam. When these problems are found online, good mills stop the line. This is why test records are just as important as the welding gear.

How Is ERW Weld Seam Quality Verified?

Mechanical Tests on the Weld

Some tests have shown that the ERW steel pipe joint can bend, get soft, and hold weight. In a flattening test, a ring cut from the pipe is smashed between plates with the weld in a certain spot. This is done to look for cracks or open seams. The weld's strength and flexibility are checked by tests that bend and pull on it. Tests like Charpy are used when the standard calls for toughness data, especially for service at low temperatures. It varies on the standard, grade, and lot size, so don't guess about how often tests should be given. Instead, look at the rules. When it comes to API 5L, it decides for itself what test frequencies are needed for high-frequency welded pipe.

Non-Destructive and Hydrostatic Testing

Online checks are done on the seam while the work is being done. These tests, like ASTM E273, use sound waves to find flaws in the weld zone that can't be seen. Some standards list eddy current and electromagnetic methods as possible alternatives. During the hydrostatic test, the pipe is then filled with water and kept under a certain amount of pressure. This checks the pipe for leaks or broken seams before it is shipped. A pipe may pass a test, but that doesn't mean it can do any work. This number is still based on the design code, the pipe's width, and the thickness of its walls. I believe the test level should be the same as what the customer will actually use it for.

Documents That Prove the Result

You can only use the test results if you can connect them to your pipe. You should ask for a Material Test Certificate (MTC) that shows the heat number, the chemical make-up, the mechanical test results, and the hydraulic test results. Many people who want to buy something want EN 10204 Type 3.1, which means that the test results have been approved by an official inspector from the manufacturer. Know the kind of person who wants to buy it. The heat numbers on the pipe should match the heat numbers on the report. Keep these papers with each lot if you are a wholesaler who resells. This will protect your image in case a buyer further down the line asks for proof. A third-party review can be added to a project when it needs extra proof.

ERW Steel Pipe Standards, Grades, and Specifications

Standards Used for ERW Pipe

One standard is for a different job. Grade B ASTM A53 pipe is the most common type. It is black and has a zinc coating that is applied hot. It is used for both mechanical and pressure purposes. One level of API 5L is PSL1, and the other is PSL2. Grades range from B to X80. ASTM A500 talks about building tubes in Grades A, B, and C. ASTM A252 has pipe piles in Grades 1, 2, and 3. ASTM A795 talks about pipes that are used in fire safety gear. So make sure you write down the exact standard on your buy order. Each one has different seam requirements, test rates, and limits. Longma Group also makes to ISO 3183, EN 10219, and AS/NZS 1163 for orders that are going to be sent abroad.

Sizes and Wall Thickness Available

Our ERW steel pipes have wall thicknesses ranging from SCH10 to SCH160 and an outside diameter ranging from 1/4 inch to 20 inches. That includes big jobs like piles and structures as well as small mechanical and fluid lines. Nominal size and schedule number are connected, so SCH40 in 2 inches is not the same wall as SCH40 in 12 inches. Make sure that the quote's outside diameter and wall are correct at all times. When you add more pressure to walls that are heavy like SCH160, you also add weight, which changes the cost of freight. Let us know what your customers always buy in the same sizes so we can give you a correct price.

Grades and Delivery for Stock Replenishment

Speed is important to distributors, but so is power. When a customer places an order before your shelves are full, our fastest shipping time of 7 days is good for restocking. Delivery times depend on the size, grade, quantity, and finish, so check each quote's date. Steel prices change all the time, so get a written quote and compare it to how long it takes you to complete an order. It's also simple to sell used oil if you pick grades that are widely used in North America, such as ASTM A53 Grade B or API 5L Grade B.

ERW Steel Pipe Compared With Other Pipe Types

ERW Versus Pierced-Billet Pipe

A pipe made from a solid billet does not have a longitudinal weld. This type of pipe is sometimes called SMLS. It is true that welded pipe is stronger in many situations, but standards like ASTM A53 say that billet-made pipe can also be used in those situations. Since ERW steel pipe starts out as a rolled strip, the wall width is usually the same all the way through. A lot of the time, the price goes down because standard sizes are easy to make. When there is a lot of pressure, heat, or wear, pierced-billet pipe might be the best choice. The best way to do it is to first read the project's needs and then choose the cheapest item that meets those needs.

ERW Versus LSAW and Spiral Pipe

Heavy-diameter jobs are done in a number of different ways. Soda arc welding is used to join plates together to make LSAW pipe. It can work with sizes and walls that are too thick for ERW. Pipe that is wound from a coil and welded together is often used for large water transmission lines. LSAW pipe and ERW steel pipe are both made by Longma Group. ERW steel pipe is usually the most cost-effective way to go for normal walls and lengths up to 20 inches. For walls that are bigger or thicker than that, LSAW is the best choice. When the process is matched to the size, it saves money and makes it clear what needs to be welded.

When ERW Is Not the Right Choice

The pipe you need may vary from job to job. If it says in the project specs that ERW steel pipe is not allowed, do what it says. Different tests need to be done for sour service, low-temperature impact, and heavy cyclic loading. For these, some owners need pierced-billet pipe. We also need to talk about corrosion. You can use hot-dip galvanizing, FBE, 2PP, 3LPE, or 3PE coats to protect ERW steel pipe that is wet, underground, or outside. You can get ASTM A795 fire safety pipe in either black or galvanized finish. You can keep your customers happy and avoid returns by making sure these conditions are met before you place your order.

How to Choose ERW Steel Pipe and Evaluate a Supplier

Define the Application First

First, think about how the pipe will work. Keep track of the operating pressure, temperature, outside loads, and environment. Write down the type of service (fire protection, water, gas, structure, piling, or fire protection). Next, choose the right height, width, grade, length, wall thickness, and end finish, such as plain, beveled, or threaded. Make rules about how straight and square the pipe can be if it is going to be made. A full blueprint helps keep mistakes to a minimum and speeds up the quote process. If you keep pipe on hand to sell instead of using it for one project, write down the three or four sizes that sell the most. That will help you choose how much to keep on hand. We can join, perforate, and grow on the other end.

Questions to Ask Any Supplier

This is a good question because it quickly shows where the risk is. What you should ask is what standard and grade the pipe meets. How do you heat the weld seam? What tests are done on it that don't damage it? Ask for a sample of the MTC and the test pressure for hydrostatics. Check the minimum order number, the available packaging choices (including whether private-label packaging is possible), the validity of the quote, the payment terms, and the Incoterm. Watch out for red flags like vague specs, certificates that don't match the product, refusals to let you view the product, or a price that doesn't include coat and test. It's usually easier to work with a supplier after the order if they answer all of your questions in writing.

How Longma Group Controls Weld Quality

Longma Group has been making ERW steel pipe and LSAW pipe on a 230,000-square-meter site since 2003. By the end of 2023, they will be making more than 1,000,000 tons of pipe every year. We get our raw materials from mills in China, such as Baosteel, TISCO, HBIS, Shagang, and Shougang. We use heat treatment to make welds stronger and testing tools to find flaws. Everything can be tracked, from the raw materials to the finished pipe. We have API 5L, ISO 9001, ISO 14001, ISO 18001 for health and safety at work, and FPC certificates. Each of the ITP, MPS, and MTC is a project paper. We sell to people in over 90 countries.

Conclusion

When the standard, the way it was made, and the tests all match up, the weld seam in ERW steel pipe is strong. It joins the edges of the strip together without using filler metal. The weld zone is smoothed out with seam heat treatment. Some tests, like tensile, flattening, bend, ultrasonic, and hydrostatic, can tell you how strong something is. Mill certificates, which are linked to heat numbers, are another way to find out. It's important to know the exact standard and grade, such as ASTM A53, API 5L, ASTM A500, ASTM A252, and ASTM A795 because they spell out different needs. ERW steel pipe is a cheap material that can be used for a lot of different things, like general purposes, building, piles, and fire safety. The pierced-billet or LSAW pipe, on the other hand, is better for some unusual or big jobs. When judging a seam, you shouldn't just look at whether or not there is a weld. You should also look at the full design and any written proof.

FAQ

Is an ERW weld weaker than the pipe body?

Not as long as the pipe is made right and checked. The seam can meet the same minimum tension and yield standards as the pipe body if the high-frequency weld is carefully controlled and then heated. Following that, flattening, bending, and non-destructive tests will be used to check the seam. Keep an eye out for those.

Can ERW steel pipe carry pressure?

Of course, as long as they don't go off track. The amount of pressure that can be put on something depends on its outside diameter, wall thickness, grade, and temperature. The designer still has to pick the right schedule and grade for the job, even if the pipe fails the hydrostatic test.

Which documents should I request?

You should ask for the Material Test Certificate, which lists the sizes, heat numbers, and results of both destructive and non-destructive tests. If your order needs them, you can add seal records and proof of origin. Find the heat number that's on the pipe and the one that's on the certificate.

How fast can Longma Group deliver?

Getting things to you the fastest takes 7 days. The real date is part of every quote because it changes based on the size, grade, amount, and coating.

Request an ERW Steel Pipe Quotation From Longma Group

Their ERW pipe is sent to more than 90 different countries. They have been making it since 2003. You can get ERW steel pipes from us in as little as 7 days. The sizes we sell and make range from 1/4" to 20", or SCH10 to SCH160. Visit longma-group.com or email info@longma-group.com with your standard, grade, size, quantity, and destination port to learn more. Based on the job, our team will get back to you with a technical idea and a price quote.