What is the difference between Schedule 40 and Schedule 80?

Home > Blog > What is the difference between Schedule 40 and Schedule 80?

Schedule 40 and Schedule 80 ASTM A53 Gr B pipe share the same outside diameter at each nominal pipe size, but Schedule 80 has a thicker wall and a smaller inside diameter. The extra steel makes Schedule 80 heavier, higher in cost per meter, and better suited to higher internal pressure and mechanical loads. Schedule 40 weighs less and gives more flow area. Both schedules can use the same Grade B steel, so the schedule describes wall thickness, not strength grade. Below, I explain how the two compare and how to pick the right one for your project.

ASTM A53 Gr B pipe

ASTM A53 Gr B pipe

Schedule 40 vs Schedule 80: Dimensions and Material Requirements

How Wall Thickness and Inside Diameter Change

Size-wise, the main difference is how thick the walls are. As per ASME B36.10M, both schedules keep the outside diameter of the same NPS the same. In other words, a thicker wall makes the bore smaller. When you look at NPS 2, the outside diameter is the same in both cases: 60.3 mm. The schedule data is below:

Schedule Wall (mm) Inside diameter (mm) Weight (kg/m)
40 3.91 52.5 5.44
80 5.54 49.2 7.48

There is about 37% more steel in Schedule 80 here, and the area where it flows is about 12% smaller. These gaps affect pressure drop, support design, lifting, and the work that needs to be done during installation. Because NPS is a label and not a measured diameter, I recommend that buyers check out the current table and project specifications before they place an order.

One Grade, Two Wall Thicknesses

The type of steel stays the same. As per ASTM A53 Gr B pipe requirements, both pipes must have a minimum tensile strength of 415 MPa (60,000 psi) and a minimum yield strength of 240 MPa (35,000 psi). There are chemical limits, such as a ceiling of 0.30% carbon and 1.20% manganese. It is not because Schedule 80 pipes are made of stronger steel that they can hold more weight; they gain capacity from geometry. A lot of the time, buyers make an error because they think that a higher schedule means a higher strength grade. We have ASTM A53 Gr B pipe in sizes SCH10 to SCHXXS, so one grade can be used for jobs with walls of different thicknesses.

Pipe Type and Documents to Confirm

Electric-resistance welding is used for Type E, and there is no weld seam on Type S. ASTM A53 Gr B pipe covers both of them. There is a Type F, but it belongs to Grade A. Buyers of Grade B choose between Type E and Type S. You should write your choice and the edition of the standard on the purchase order.

Files and dimensions are both important. You should request a mill test record that shows heat number, chemistry, and mechanical results, as well as hydrostatic test records and dimensional reports. We provide documents like MTC, Inspection and Test Plan, and Manufacturing Procedure Specification here at Longma Group. Plus, we trace products from raw material to finished pipe, which helps your inspector confirm compliance before material leaves the yard.

Pressure, Temperature, and Application Differences

Why Schedule Alone Does Not Set a Pressure Rating

When it comes to the same size and grade, Schedule 80 does carry more internal pressure than Schedule 40. However, this is because the thicker wall lowers hoop stress. There is no set pressure rating that equals a schedule number alone. Engineers calculate the allowable pressure using a governing code, such as ASME B31.3 for process piping. To do the math, they use allowable stress, design temperature, weld joint factor, and corrosion allowance. They also account for mill tolerance, since ASTM A53 Gr B pipe allows wall thickness to drop as low as 87.5% of nominal. Please share the required minimum wall from your engineer so we can match it to the correct schedule.

Temperature Limits and Steam Service

ASTM A53 Gr B pipe suits water, air, steam, and oil in low- and medium-pressure service. It can also be used as structural steel. High-temperature, high-pressure service, such as power generation, usually calls for ASTM A106 Grade B, which is made only without a weld seam. The thicker wall of an ASTM A53 Gr B pipe does not change it into an A106 pipe. If A106 is named in the project specification, you should get written approval from the engineer before any substitution. Talk to the responsible engineer about the design temperature and pressure for steam lines before choosing either schedule.

Where Each Schedule Fits in Practice

Because its larger bore keeps friction loss lower, Schedule 40 is common in water distribution, compressed air, utility lines, mechanical systems, and general fabrication. Schedule 80 fits higher pressure, impact exposure, heavier mechanical loads, and extra corrosion allowance. For threaded joints, cutting threads removes metal, and a thicker wall leaves more metal behind. For structural and piling work, engineers should check bending, buckling, and axial load rather than pick a schedule by thickness alone. For outdoor exposure, hot-dip galvanizing adds corrosion protection, and Longma Group offers it along with other coating options.

Cost and Procurement Impact

Weight, Freight, and Installation Cost

The material cost, freight, and handling all rise with Schedule 80 because it uses more steel per meter. On an NPS 2 100-meter run, Schedule 40 weighs about 544 kg and Schedule 80 weighs about 748 kg, a difference of about 204 kg before supports and fittings. Thicker walls also require more filler metal and add welding time. The lowest price per ton does not always mean the lowest project cost. I suggest comparing equal specifications, including type, schedule, length, ends, coating, testing, and packing. A fair comparison protects your budget from surprises after the award.

Stock and Lead Time Planning

It is important to think about both price and lead time because late pipe can trigger schedule penalties. Longma Group keeps 200 to 300 tons of ASTM A53 Gr B pipe in stock at all times. Depending on specification and quantity, the fastest delivery starts from 7 days. Our range covers NPS sizes from 1/8" to 26", schedules from SCH10 to SCHXXS, and lengths from 3 to 12.5 meters. Project changes often bring small add-on quantities, so let us know early, and we will review our stock. For U.S. destinations, add ocean transit and customs clearance to your delivery plan, and confirm exact availability when you send your inquiry.

A Procurement Checklist That Prevents Rework

A complete purchase order closes specification gaps before they cause delays. I suggest listing the ASTM A53/A53M edition, Grade B, Type E or Type S, NPS, schedule, length, and end finish. Add the design pressure, design temperature, governing code, and surface treatment. Then list the documents you need, such as the MTC, hydrostatic test records, dimensional reports, and any third-party inspection. Finish with the Incoterm, destination port, packing, and delivery date. Sending all of this at once lets a supplier confirm technical fit, price, and lead time in a single reply, which shortens your comparison period.

Choosing Between Schedule 40, Schedule 80, and Other Standards

How ASTM A53 Gr B Compares with A106 and API 5L

ASTM A53 Gr B pipe can be welded or made without a weld seam, serving mechanical, structural, and low- to medium-pressure piping. ASTM A106 is limited to pipe without a weld seam and targets high-temperature service. API 5L covers line pipe for oil and gas transmission. The three standards may share similar dimensions, yet they differ in manufacturing scope, chemical limits, testing, and supplementary requirements. Never substitute one standard for another unless the engineer of record approves it in writing. The purchase order should name the standard, grade, type, schedule, and inspection requirements clearly.

A Four-Step Method to Select the Schedule

Start with the service conditions: fluid, pressure, temperature, flow rate, corrosion, and external loads. Second, check that the design code accepts ASTM A53 Gr B pipe and states whether Type E or Type S is required. Third, calculate the minimum wall thickness, adding the corrosion allowance and the 12.5% mill tolerance. Fourth, choose the lightest schedule that meets or exceeds that result, then check that fittings, valves, and supports match. This order keeps cost under control. Schedule 80 earns its place when the calculation or the specification requires it, not because it looks stronger.

Matching Fittings, Flanges, and Welding

Equal outside diameters do not mean every component fits perfectly. ASTM A53 Gr B pipe is a good example of why matching outside diameter alone is not enough. Butt-weld fittings come with a defined wall thickness, so joining them to pipe with a different wall creates an internal step that may need a transition bevel. Flanges, valves, and gaskets also carry their own pressure classes. Your welding procedure should cover the wall thickness you plan to weld. Longma Group provides welding, perforating, expanding, and other end treatments for mating connections, which helps site crews fit pipe to the components already on the project.

Why Work with a Qualified ASTM A53 Gr B Pipe Supplier

Manufacturing Experience Behind the Pipe

Hebei Longma Group Limited has produced ERW and LSAW steel pipe since 2003 on a site of 230,000 square meters. Our annual output passed 1,000,000 tons by the end of 2023, shipping to more than 90 countries. We source raw materials from domestic mills, including Bao Steel, TISCO, BX Steel, Shougang, and HBIS. Heat treatment is applied to strengthen welds, and inspection equipment is used to detect inconsistencies. We trace each product from raw material to finished pipe, ensuring batch consistency across repeat orders.

Quality Systems and Documentation

Contractors often check whether a supplier really follows ASTM requirements. The best answer is paperwork your inspector can check. Longma Group holds API 5L, ISO 9001, ISO 14001, ISO 18001, and Factory Production Control certificates. For each order, we provide an Inspection and Test Plan, a Manufacturing Procedure Specification, and a Material Test Certificate. Review these against your project specification before shipping, and share any inspection requirements with us so we can discuss them. Clear records reduce disputes at the receiving yard and keep installation on schedule.

Services That Save Time on Site

Our customers include engineering contractors, stockists, and import traders, so we support more than pipe supply. Fabrication options include welding, perforating, expanding, and end treatments. Anti-corrosion options include hot-dip galvanizing, FBE, 2PP, 3LPE, and 3PE. Ordering coated or end-prepared pipe from one source can reduce handling steps between mill and site. If your project needs a mixed order of Schedule 40 and Schedule 80, send the size list together, and we will check stock and delivery timing for both. Payment terms and top-up quantities are easier to settle at the quotation stage, so raise them in your first message.

Conclusion

Schedule 40 and Schedule 80 ASTM A53 Gr B pipe differ in wall thickness, not in steel grade. For each NPS the outside diameter stays the same, so Schedule 80 has a smaller bore, more weight, and a higher cost per meter, while Schedule 40 gives more flow area and easier handling. Pressure capacity depends on the design code, temperature, corrosion allowance, and wall tolerance rather than the schedule number alone, and high-temperature service may require A106 instead of A53. Pipe type, fittings, welding procedures, documents, freight, and lead time also shape the final choice. The right schedule is the lightest one that satisfies the calculated wall and the project specification.

FAQ

Is Schedule 80 pipe made from stronger steel than Schedule 40?

Not at all. Both can be ASTM A53 Gr B pipe with the same minimum yield and tensile strength. Schedule 80 simply has a thicker wall, which raises pressure and load capacity in the same size.

Can Schedule 40 and Schedule 80 use the same fittings?

Not always. Outside diameters match, but butt-weld fittings follow a set wall thickness, and a mismatch creates a joint step. Confirm each fitting's schedule and pressure class before ordering.

Is ASTM A53 Gr B pipe suitable for steam?

It can serve low- and medium-pressure steam when the design code permits it. High-temperature, high-pressure steam often calls for A106 Grade B, so have your engineer confirm the design conditions.

What do I need to send for an accurate quotation?

Send the specification and edition, Grade B, Type E or S, NPS, schedule, quantity, length, end finish, coating, destination, and any required documents. Pressure and temperature help us confirm suitability.

Request an ASTM A53 Gr B Pipe Quotation from Longma Group

Email info@longma-group.com with your size list, schedule, quantity, and destination, and our team will review your ASTM A53 Gr B pipe requirements. As an ASTM A53 Gr B pipe supplier with 200–300 tons in stock and delivery from 7 days, we provide MTC documents and coating options. Visit longma-group.com for more details.