What is the difference between S235JRH, S275J2H and S355J2H?

Home > Blog > What is the difference between S235JRH, S275J2H and S355J2H?

The main differences between S235JRH, S275J2H, and S355J2H are yield strength and impact toughness. Under EN 10210, S235JRH has a 235 MPa minimum yield strength and a 27 J impact value at +20°C. S275J2H raises the yield strength to 275 MPa and moves the 27 J test to −20°C. S355J2H reaches 355 MPa with the same −20°C test. An EN10210 pipe in S355J2H therefore carries the highest load of the three, while both J2 grades suit colder service. I will walk you through each grade, the standard behind it, and how to order with confidence.

EN10210 pipe

EN10210 pipe

What Are S235JRH, S275J2H, and S355J2H?

How the Grade Codes Work

The grade names are short, but they say a lot. The "S" stands for steel used in building. The number tells you the lowest stress strength in MPa, which is 235, 275, or 355 if the walls are thin. "JR" means the steel has to pass the Charpy V-notch test with 27 J at +20°C. "J2" means it has to pass with the same 27 J at -20°C. The letter "H" looks like a flat surface. A grade called J0 is also tested at 0°C. An example of a hollow section is S355J2H, which has a yield strength of 355 MPa and a hardness at -20°C. When I read one of these letters, I quickly know what the buyer's expert wants from the steel.

Where EN 10210 Applies

Part of EN 10210 is structural hollow sections made of fine grain and non-alloy steels that have been hot finished. In Part 1, the rules for technical delivery are laid out. In Part 2, the tolerances, measurements, and qualities of the sections are laid out. Pieces that hold weight in building frames, beams, columns, and bridges are covered by this standard. They can be round, square, or rectangular. In general, it doesn't cover fluid or pressure pipes. People can use "EN10210 pipe" in everyday speech. Scientists, on the other hand, see the item as an empty piece for structure and check it against the rules in Eurocode 3 (EN 1993).

Why Yield Strength Alone Does Not Decide

If the number is big, it doesn't always mean it's the best choice. The minimum yield strength goes down a little as the wall thickness goes up. This means that an S355J2H section with thick walls does not carry exactly 355 MPa. The service temperature lets us know if the JR toughness is enough or if we need the J2 toughness. It's also important to follow the plans for welding, galvanizing, and manufacturing steps. The project engineer has to sign off on the end grade. First, you need to get four things: the load case, the wall thickness, the lowest design temperature, and the rules for getting your project approved. After that, compare the grades. That order keeps the delivery from being turned down at inspection, which saves time.

S235JRH vs S275J2H vs S355J2H: Key Mechanical Property Differences

Strength and Ductility Side by Side

In the table below, you can see the EN10210 pipe values in EN 10210-1 for the thinnest common walls. For each grade, the minimum yield is 16 mm, the minimum tensile strength is 40 mm, and the minimum elongation is 40 mm. The impact test is done. The grades are S235JRH, which has 235 MPa, 360–510 MPa, 26%, and 27 J at +20°C; S275J2H, which has 275 MPa, 410–560 MPa, 22%, and 27 J at -20°C; and S355J2H, which has 355 MPa, 470–630 MPa, and 27 J at −20°C.

It gets stronger as the grade goes up, but it can't stretch as much. The yield value also drops as the wall gets stronger. The stress in S355J2H drops to 345 MPa between 16 and 40 mm. In order to follow the current standard, you should always make sure that the wall width numbers you use are correct.

JR Versus J2 Impact Toughness

Impact toughness is a way to rate how well steel can handle being quickly broken. It says 27 J for JR grades at +20°C and -20°C for J2 grades, which is 40°C cold. For frames, bridges, and projects outside in cold places, that gap is important because steel gets weaker when it cools. Don't forget that the temperature you use is different from the temperature you test it at. EN 1993-1-10 tells makers how to pick the right material for a certain temperature. It's possible that a thick wall needs more strength than a thin wall. Because of this, S275J2H is often better than S235JRH when power is not important.

Strength, Stiffness, and Connections

All three grades have the same modulus of elasticity, which is about 210 GPa. In other words, a stronger grade doesn't make a member stiffer. It is often buckling, local stability, and deflection that decide where the section size comes from. This is when S355J2H might not save as much weight as you think. The grade affects not only how the link works and how it handles fatigue, but also the quality of the weld and the shape of the joint. High-strength grades also need extra care when they are welded, and the way they fit together depends on the wall thickness and tolerances. Please talk to your expert about these points and write down all of your delivery needs in the order.

Which Grade Should You Choose?

S235JRH and S275J2H in Practice

For normal situations with light loads, like secondary frames, supports, and indoor structures, S235JRH is a cheap choice. It's the S275J2H in the middle. So it's good for projects with cold winters and roof trusses and posts that are out in the open. It's stronger than S235JRH and tougher at -20°C. S275J2H is often the first choice for people who want J2 toughness but don't want to pay the most for power. The work of your engineer is still the most important thing because the grade is based on the design code and the load case, not on what you usually do.

S355J2H for Heavy-Duty Work

The steel grade S355J2H is used for things like bridges, cranes, offshore platforms, and industrial steelwork that need to be strong and able to hold a lot of weight. EN10210 pipe in this grade is a common choice for such projects. When it comes to building, its higher yield strength means that the part can be thinner or smaller while still holding the same amount of weight. This cuts down on weight, shipping costs, and the amount of repair that needs to be done. In the long run, though, the best mark doesn't always cost the least. We lose the extra strength as we need to bond and build more things if we don't use buckling or deflection limits. For jobs near the coast or offshore, it's also important to protect against corrosion, since none of these grades are enough to stop it by themselves.

A Simple Selection Path

First, put the least amount of load and heat on it. Check to see if the limit is for how much something can bend or move. Go over again the thickness of the wall and the conditions for welding. Then, talk to your structural engineer about the grade and the rules for getting the project approved. Last but not least, send a full quote request that includes the shape, size, impact test needed, and any documents. If you do it this way, you won't waste money on strength that you can't use or that isn't right for the site.

EN10210 Pipe Manufacturing, Standards, and Dimensions

What Hot Finished Means

What is "hot finished"? Either the hollow part is formed while the thing is hot, or it goes through a heat treatment that makes it act like it was hot formed. It doesn't mean the item doesn't have a weld line. EN 10210 says that things can be made both with and without welding. Sections that are hot-finished tend to have less leftover stress and more uniform properties across the section than sections that are cold-formed. This makes them better for members and columns that are very full. You should still check the straightness, wall thickness, and surface condition of a shipment against the Part 2 tolerances before accepting it.

EN 10210 vs EN 10219

EN 10219 talks about hollow pieces that are cold-formed and joined. Because there are different ways to shape the material, there are also different sizes, shapes, and patterns of leftover stress. If the job needs a hot finish, EN 10210 is often a good choice for heavy walls, long parts, and columns that hold a lot of weight. When the plans and paperwork allow it, EN 10219 can be a good choice for cold-formed sections. There are times when neither is better than the other. Don't change from one standard to another until the engineer agrees, the proof is looked over, and the customer signs off on it in writing. We can give you a quote for any of the EN 10219 S235, S275, and S355 grades in JRH, J0H, and J2H.

EN 10210 vs API 5L and ASTM A106

You can't switch out steel pipes. EN10210 pipe is not the same as line pipe, and the two should not be used interchangeably. EN 10210 talks about parts of structures that are empty but can hold weight. This pipe moves oil, gas, and other chemicals. It's named API 5L line pipe. It is made of carbon steel and is meant to be used at high temperatures. It doesn't have a weld seam. These standards have different goals, science limits, tests, sizes, and ways to get certified. A simple "steel pipe, 12 inch" order is most likely not what it should be. List the product's standard, grade, shape, size, test standards, certificates, amount, destination, and due date for delivery. The short list helps the seller figure out the best price for the item the first time.

EN10210 Pipe Quality, Certification, and Supplier Evaluation

Documents to Request

The first step in compliance work is to fill out forms. Tell them what kind of Mill Test Certificate you need, such as EN 10204 3.1. The heat number, chemistry analysis, tension results, and Charpy impact results for that grade must all be shown. For items that have been welded, add dimensional data and NDT records for the weld line. With its heat number, each bundle can be linked to its test results. You can get MTC, an Inspection and Test Plan (ITP), and a Manufacturing Procedure Specification (MPS) when you order from Longma Group. There are marks for ISO 9001, 14001, and 18001 on our company that come from FPC. Tell us if your project needs impact tests to be watched by someone not working on the project when you ask.

Judging a Supplier and Our EN10210 Pipe Range

Seek out companies that have dealt with EN 10210 grades before, can handle thick walls and large diameters, use quality methods, can package for export, and can show up on time. There has been an ERW and LSAW steel pipe company in Hebei since 2003. This year, we sent more than 1,000,000 tons of goods to more than 90 countries. This will end in 2023. There are three kinds of EN10210 pipe we offer: S235, S275, and S355. Sizes run from 3" to 80" around, and wall thickness is between SCH10 and SCH160. We have 50–150 tons in stock, and shipping will begin in 7 days. You can pack your things in a bag, a wooden box, or a wooden board. Steel from mills like Shagang, TISCO, HBIS, and Baosteel gets to us, and we can follow it from the time it is made to the time it is sold. Price depends on grade, size, testing, shipping, packaging, and the market.

Common Mistakes and Inquiry Checklist

Four mistakes keep happening. People opt for items based only on price, and then they spend extra on bigger or better parts. They always believe that S355J2H is the best, even when it comes to controlling buckling. They don't compare JR to J2 on projects that need to be done in cold weather. They mix structural hollow sections with API 5L or ASTM A106 pipe. With a full probe, you can avoid all four. As an example: "EN 10210 S355J2H, circular hollow section, 323.9 mm OD, 12.5 mm wall, 12 m lengths, 27 J at -20°C, MTC EN 10204 3.1, 80 tons, bundled, delivery to Houston." You can get the right price by entering the payment terms, limits, surface finish, and end state.

Conclusion

The standard yield strengths of EN10210 pipe are 235 MPa for S235JRH, 275 MPa for S275J2H, and 355 MPa for S355J2H. There were tests done on JR at +20°C and tests done on J2 at −20°C. These grades are part of EN 10210, a standard for structural hollow pieces that are hot-finished. EN 10219 is a standard for cold-formed sections, and this standard is different from those. It is also different from API 5L and ASTM A106 pipe. Which grade to use depends on the loads, the lowest design temperature, the thickness of the wall, the ability to buckle, bend, or weld, and the engineer's approval. In other words, the best grade isn't always the strongest. With a mill test certificate, a heat number that can be tracked, and a full specification, it is clear that the material provided fits the plan.

FAQ

Is S355J2H stronger than S275J2H?

While S275J2H's minimum yield strength is only 275 MPa for thin walls, S355J2H's is 355 MPa. Both are put to the test at -20°C and 27 J.

What separates S235JRH from S275J2H?

The main difference between S235JRH and S275J2H is that S275J2H has a higher yield strength (275 MPa vs. 235 MPa) and its impact test runs at -20°C instead of +20°C.

Can I replace S235JRH with S355J2H?

Sometimes, but only if an engineer says it's okay. It is possible for the price, the way the connection is made, and the welding process to change.

Are EN 10210 sections always made without a weld seam?

The standard says that both welded and non-welded hot finished paths are fine.

Do these grades resist corrosion?

No, they need to be zinc-coated or coated. It is possible for Longma Group to hot-dip galvanize and coat things in other ways.

Request an EN10210 Pipe Quotation for S235JRH, S275J2H, or S355J2H

Right now, send Longma Group what you need in S235JRH, S275J2H, or S355J2H. Our team will give you a clear price based on the grade, size, wall thickness, number, plans, and other information you give us. We have 50 to 150 tons of EN10210 pipes in stock that we sell. We can give you an FPC certificate and MTC forms and send them to you in as little as 7 days. Email info@longma-group.com or go to longma-group.com to start your question.